Here is a number most suppliers will not bring up: on a site with real dust, a dirty panel can lose you 15-20% of your daily charging. Not because the panel is bad, but because a 1mm layer of grit blocks light before it ever reaches the cells. Multiply that across a year and you are either running a bigger battery than you needed, or a dimmer light than you promised.
So we built the LRQX series around one question: what if the light cleaned itself?
![]()
A roller broom brush travels along an inner rail across the panel face, sweeping dust into a collection channel. The brush is detachable, so when it wears out you swap the brush, not the panel. The whole thing runs on its own schedule from the controller, usually early morning when dew has softened the dust.
Real-world effect: charging speed goes back up by roughly 15-20% on a dusty site, which is the difference between a 3-day and a 5-day rainy-season buffer on the same battery.
The lights talk LoRa to a gateway (JWL-SWC), and that gateway talks to your computer over 4G, 3G or GPRS. You get status, on/off, dimming and fault reports per lamp from a browser, without running a single control cable down the road. For a 60-pole layout that is the difference between a two-week commissioning and an afternoon.
| Spec | 60W | 80W | 100W |
|---|---|---|---|
| Luminous flux | 8400Lm | 11200Lm | 16000Lm |
| LED chips | 144 | 256 | 256 |
| PV module | 18V 60W | 18V 70W | 18V 100W |
| LiFePO4 | 12.8V 30Ah | 12.8V 36Ah | 12.8V 48Ah |
| Dimension / N.W. | 1233x373x50 / 20.6kg | 1543x373x50 / 22.8kg | 1863x373x50 |
![]()
All three run 210Lm/W, 2700-6500K, 150x75 degree beam, with PIR or time control.
1. Does the brush scratch the glass? The brush is a soft nylon roller on fixed rails, the same idea as a ticket printer. It rides on the frame, never on the glass, and the pressure is set by the rail height.
2. How often does it clean? Set it daily, weekly or twice weekly from the controller, depending on how dusty the site is. Most buyers run once every two days in dry season, once a week in the rainy months.
3. What if the brush motor fails? The panel still works, you just lose the cleaning function. The brush assembly is detachable and replaceable as a spare part, and the motor circuit reports a fault to the LoRa dashboard.
4. Do I need the LoRa gateway for one lamp? No. A single lamp works standalone with PIR and time control. The gateway pays for itself from about 10-15 lamps upward, or wherever you cannot reach the pole easily.
5. Can it run without sun for a week? No, and be suspicious of anyone who says yes. On the 100W the pack is 12.8V 48Ah, sized for normal cloudy stretches with the dimming profile. For extreme sites we upsize the panel.
6. Is the pole included? The hard-pressed pole is available as an option; the light fits standard pole diameters with our bracket, so you can also retrofit existing poles.
Our plant covers 30,000 m² with three assembly lines and two in-house SMT lines for the driver boards. Every fixture spends 48 hours at full load in the aging room, each batch gets an IP66 spray test, and packed cartons are drop tested before palletising. Twelve inspection points travel with the goods on a traveler card, so any serial number traces back to the shift that built it. Monthly output for this series is around 1,000 sets, so a 300-set order is a normal run. Housing colour, logo and manual language from 50 sets; lead time 20-25 days, samples in 7.
If dust is the reason your current lights underperform, send us the site photos and we will tell you whether cleaning alone closes the gap, or whether you need a bigger panel.